Pinnacle West Spray Foam and Coatings Specialists Since 1998 Like Us On Facebook. Follow Us On Twitter. Visit Our YouTube Channel.
Graco Top 20 Distributor

Free Shipping on orders over 50$

  • Your cart is empty

    You have no items in your shopping cart.

Indy Blast Black Cartridge

SKU: C2+.BLK.01

Availability: Order Online or by Phone at 1-800-901-0088

  • Buy 12 for $27.00 each and save 4%
  • Buy 24 for $26.00 each and save 8%
  • Buy 48 for $25.00 each and save 11%
  • Buy 60 for $24.00 each and save 15%
Indy Blast Black Cartridge is available for purchase in increments of 6

Quick Overview

INDY BLAST is a 100% solids, two component, polyurea hybrid coating. Indy Blast is primarily used for lining truck beds, van and SUV interiors or the repair of existing sprayed on bedliners.

Indy Blast Black Cartridge

Zoom Out
Zoom In



INDY BLAST Cartridges are only available for purchase in increments of 6 cartridges.
Example 6, 12, 18, 24 etc...

INDY BLAST is a 100% solids, two component, polyurea hybrid coating. Indy Blast is primarily used for lining truck beds, van and SUV interiors or the repair of existing sprayed on bedliners.

Other automotive uses include undercoating and rocker guard protection. Indy Blast also works well as a protective coating on utility trailers, horse and boat trailers. Cartridges come pre-pigmented. Contains no volatile organic compounds (VOC's).

The INDY BLAST Spray-On coatings are the real thing. Industry proven for over a decade and until now applied only with expensive equipment; the INDY BLAST coatings are the most economical solutions to professional grade applications where an anti-slip, chemical resistant, abrasion proof coating is absolutely necessary.

Includes Each cartridge includes one mixing tube with retainer nut and air cap
Shore Hardness 88 - 92 Shore A
Gel Time 14 - 16 seconds
Elongation @ Break 240 - 260 %
Tensile Strength 2000 - 2200 psi
Tear 295 pli
Coverage One Indy Blast cartridge will cover:
16 sq. ft. at 40 mils
8 sq. ft. at 80 mils
5 sq. ft. at 125 mils
Storage INDY BLAST has a shelf life of 6 months in unopened containers, avoid exposure to freezing temperatures
Spec Sheet Click here to view Spec Sheet
MSDS Click here to view MSDS
Notes Cartridges should be pre-conditioned to 75-80°F (24-27°C) prior to use

The Indy Blast Cartridge system is quick and easy to use. Whether you are a professional applicator or new to fast set coatings, you will be able to spray Indy Blast with ease.

Indy Blast Application

Apply INDY BLAST using our pneumatic spray dual cartridge gun. Cartridges should be pre-conditioned to 75-80°F (24-26°C) before using. Ensure that the compressed air source is dry, and can provide a constant pressure of 110 psi. The compressor should be rated to deliver 10 CFM at 100 PSI minimum. Use the static mixer with the air atomizer tip supplied with your cartridges. With 110 psi inlet pressure, set fluid flow to maximum and airflow to the atomizer at 25 - 45 psi.

Start spraying on a piece of cardboard or other disposable surface until an acceptable spray pattern is achieved. When a spray pattern has been achieved, this should take 2-3 seconds; fan over to the object staying about 18 inches from the target, working with even passes, building coats to desired thickness. Spray at a right angle to the target moving the gun and not your wrist. Visually monitor material levels and cease coating work just prior to emptying cartridges to ensure that an even ratio of the material is applied to the surface. INDY BLAST can be textured with typical over-spray techniques.

If you need to stop spraying mid-cartridge you will need to replace the mixing tube before continuing. If you have not completely used the full cartridge and would like to save the rest for another job, leave the mixing tube attached to the cartridge, the INDY BLAST material will harden in the mixer which acts as a seal until ready to use again. When ready to use the rest of the cartridge remove hardened mixer, replace with a new mixer and start spraying once again.


Any persons inside the spray area must wear an approved respirator (full- or half-face air-purifying respirators which are niosh-certified with organic vapor cartridges with dust/mist [dm] or high efficiency [hepa] filters). If airborne concentrations exceed or are expected to exceed the TLV, use MSHA/NIOSH approved positive pressure supplied air respirator with a full-face piece or an air supplied hood. Always spray in a well ventilated area.

Review by Scott

(Posted on 5/30/15)

Great product

Was a bit worried that I was spending money on a product that wouldn't work. Turns out I was wrong, Gun was a bit of a challenge to get the hang of but once you figure it out, you end up with a professional install that lasts and is as tuff as nails. I have sprayed it on metal and wood so far and both applications are working great still.

Review by Tony

(Posted on 7/19/11)

Nice Product

We are a GM and Chrysler dealer and we have sprayed many of these black liners. Once you have truck ready, it takes just a few minutes to spray and its done. They always seem to look nice and customers are happy with results.

Review by Carl

(Posted on 7/18/11)

Easy To Learn

Very easy to learn and get great results! Low initial cost for equipment and you can buy supplies as you need them. Pay attention to the instructions as they relate to cartridge temperature and air compressor capacity, they are very important to good results!

Add Your Review

If you would like to add a review please log in to your account or register for a free account.

Other people marked this product with these tags:

Use spaces to separate tags. Use single quotes (') for phrases.

Compare Products

You have no items to compare.

Have questions, call us toll free at

  • Quality Products
  • Rewards Program
  • Technical Support
  • Easy Return Policy
  • Massive Selection
  • Fast Shipping